Why does my Lux thermostat say Stage 2?

2″ is displayed when the thermostat is turning on the first and second stages of a conventional heating system. “AUX” is displayed when the thermostat is turning on the first and auxiliary heating stages on a heat pump.

Subsequently, Why does my thermostat say ol?

Shows “OL” “OL” means Out of Limits. The sensor is reading outside the thermostats display limit of 32°F to 95°F. When the temperature returns to within these limits the temperature display will reappear. If actual room temp is not outside these limits, there may be a malfunction.

then, What does flashing flame on Lux thermostat mean?

Showing 1-3 of 3 answers. Rob the Flame symbol when flashing alerts you to the is furnace running until the furnace cuts off then flame symbol stops flashing. This is the normal operation. LUX Technical Support.

Thereof Why does my Lux thermostat say low battery? You can resolve low battery issues on your Luxpro Thermostat by putting in fresh AA alkaline batteries of either Energizer or Duracell in the correct orientation. If this does not fix the issue, reset the Thermostat.

What does heating stage 2 mean?

Two-stage heating means the furnace has two levels of heat output: high for cold winter days and low for milder days. Since the low setting is adequate to meet household heating demands 80% of the time, a two-stage unit runs for longer periods and provides more even heat distribution.

21 Related Questions Answers Found

How do you fix a Lux thermostat?

How do I reset my thermostat?

Take the front of the thermostat off the wall and look for a small white round reset button on the right side labeled “H.W. Reset”.
Hold this button down for at least 5 seconds.
The screen should fully populate temporarily.

How do I know if my thermostat is 24v?

You probably have a low voltage (24v) system if…

You have 2 to 9 (or more) wires.
Those wires are low gauge (rather thin compared to other electrical wiring)
Your wires are multicolored (red, white, green, orange, blue, black)
You have a furnace somewhere in your house – basement, garage, bathroom, etc.

How do you bypass a Lux thermostat?

How to Unlock a Lux 1500 Thermostat

Press and release the “Next” button, in the center of the thermostat’s programming panel, three times.
Press the “Hold” button, and then release it. …
Press and release the “Next” button three times, and then press and release the “Hold” button to lock the thermostat again.

How do you control a Lux thermostat?

How do I set a hold?

Thermostat must be in either heat or cool position.
SET Slide switch must be in the RUN position.
Press the HOLD key to turn HOLD on and then again to turn it off.
HOLD is only active when the word “HOLD” is visible in the display.

Why does my thermostat keep flashing?

If you see a flashing light on your thermostat, that’s a signal that there’s a problem with your outdoor unit. When this happens, your outdoor unit will shut off and send a signal to your thermostat, causing it to blink. Thing is, that signal doesn’t mean your indoor unit is made aware of the problem.

How do I change the batteries in my Lux thermostat?

To replace the batteries in the thermostat:

Remove the thermostat’s body from the base plate attached to the wall.
Remove the used batteries from the battery tray and discard appropriately.
Install two new Energizer or DURACELL, “AA” size alkaline batteries into the battery tray.

Why does my thermostat say low battery after changing batteries?

If your Honeywell programmable thermostat flashes “Batt Lo,” you simply need to replace the battery. If the thermostat is malfunctioning and will not reset, simply cut the power to the thermostat and it will reset itself.

How do you program a Lux tx700u?

TO SET A TEMPERATURE PROGRAM: Choose either HEAT or COOL mode. Move the Set Slide switch to the TEMP PROG position. Programming will start with Monday. Use the UP/DOWN buttons to adjust the start time for the MORN period, and then press the NEXT button to advance.

Is a 2 stage furnace better than a single-stage?

Having two “on” modes allows a two-stage furnace to reduce temperature fluctuations and heat your entire home more evenly and efficiently than a single-stage furnace. However, this higher efficiency does come with a higher price tag.

Do 2 stage furnaces run more often?

Because two-stage furnaces can operate at a lower setting based on the actual heat required, as well as spend more time at that setting, they can often use less fuel than standard furnaces, which turn on and off (cycle) more frequently.

Are Single-stage furnaces more reliable?

Most 90%-plus single-stage furnaces are 90% to 95% efficient. A few are higher. The Carrier Performance Boost 90 furnace offers an outstanding 96.5% AFUE. A two-stage furnace runs at 70% capacity most of the time it is heating.

How do you clear a thermostat override?

To clear OVERRIDE press UP/DOWN until original set temperature appears or wait for the start tf the next period. Press HOLD. Adjust temperature as desired with UP/DOWN. To clear, press HOLD again.

How many volts is the C-wire?

The c in c-wire stands for common. The purpose of the thermostat c-wire is to provide continuous 24-volt AC power, known as 24VAC, to the thermostat. And the purpose of having continuous power is to get a constant, accurate thermostat reading.

What if there is no C-wire for thermostat?

If you don’t see a wire you can identify as the C-wire, though, don’t despair yet – you may need to look behind your existing thermostat. If your current thermostat didn’t need a C-wire, it (or a wire that can be used as a C-wire) might be rolled up inside the wall.

How do you program a Lux?

TO SET THE HEAT TEMPERATURE PROGRAM

While in HEAT mode, press MENU, then the SCROLL button one time, and “SET / REVIEW HEAT PROGRAMS” should be displayed at the top of the screen. Press OK. This will program all 7 days of the week, each day separately, in order of Mo, Tu, We, Th, Fr, Sa, Su).

How do I reset my digital thermostat?

A common way to reset almost any thermostat is to hold down the reset button for 5+ seconds. Alternatively, try resetting battery-powered thermostats by flipping the battery directions around for 5s, then flip them back. If all else fails, switch off the power at the circuit breaker for a couple minutes.

What is reset button on thermostat for?

Hold Temperature – You can use this button to set the temperature to remain at that level until you change it again. This is most helpful if you know you will not be home all day, like if you go away for a day trip, so you set the temperature to a lower setting, not to be reset until you return.